Welltech Dialogic SS7 Protocols ISUP Manual de usuario Pagina 33
- Pagina / 203
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Dialogic
®
SS7 Protocols ISUP Programmer's Manual Issue 15
33
6.5.8 End-to-End Message Request
This primitive is used by the application for end-to-end signaling.
Message type
PAM (Pass Along Message)
Mandatory parameters
• Message data
Optional parameters
None
6.5.9 Exit Request
Note: This message is only applicable to ANSI operation
An Exit Message may be sent in the backward direction from a gateway
exchange before Address Complete to indicate that call setup information has
successfully been passed to an adjacent network. This message may be
issued by the application for an incoming call in the waiting ACM state and
will only be accepted if the ISPGOP_ANSI circuit group option is selected.
Message type
CPG (Call Progress Message)
Mandatory parameters
• Event information
Must be coded as value 0x7d (defined as ‘spare’ by ANSI T1.113.3), to
indicate Exit.
Optional parameters
• Outgoing trunk group number
6.5.10 Facility Request
This primitive is used by the application to request activation of a particular
facility or action at another exchange.
Two forms of this primitive are supported. FAR is used to request a particular
facility during the active (speech) phase of a call, and FAC is used during
either the setup or active phase of a call to request a particular action at
another exchange.
Facility Request
Message type
FAR (Facility Request Message)
- Dialogic 1
- SS7 Protocols 1
- Contents 3
- Figures 6
- Revision History 7
- About this Publication 9
- 1.3 Related Documentation 10
- 1.4 Feature Overview 11
- 2 General Description 13
- Value Mnemonic Meaning 14
- 3 Internal Data Structures 17
- 4.1 System Functions 19
- 4.2 Timer Operation 19
- 5 Interface to MTP 21
- Section 5 Interface to MTP 22
- 6 Interface to Application 23
- 6.2.2 Receive Indication 24
- 6.5.1 Alerting Request 28
- 6.5.6 Confusion Request 32
- 6.5.7 Continuity Request 32
- 6.5.9 Exit Request 33
- 6.5.10 Facility Request 33
- 6.5.11 Facility Response 35
- 6.5.15 Information Request 37
- 6.5.19 Overload Request 40
- 6.5.21 Proceeding request 41
- 6.5.22 Progress Request 42
- 6.5.23 Release Response 43
- 6.5.24 Release Request 44
- 6.5.26 Resume Request 45
- 6.5.27 Segmentation Request 46
- 6.5.28 Setup Request 46
- 6.5.29 Setup Response 49
- 6.5.31 Suspend Request 52
- 6.6.1 Alerting Indication 56
- 6.6.6 Confusion Indication 60
- 6.6.7 Continuity Indication 61
- 6.6.9 Exit Indication 61
- 6.6.10 Facility Indication 62
- 6.6.11 Facility Confirmation 63
- 6.6.19 Overload Indication 68
- 6.6.21 Proceeding Indication 69
- 6.6.22 Progress Indication 70
- 6.6.23 Release Confirmation 71
- 6.6.24 Release Indication 71
- 6.6.26 Resume Indication 73
- 6.6.28 Setup Confirmation 74
- 6.6.29 Setup Indication 76
- 6.6.31 Suspend Indication 79
- 6.7 Parameter Definitions 80
- 6.7.1 Called Party Number 86
- 6.7.2 Calling Party Number 86
- 6.7.3 Cause Indicators 87
- 6.7.4 Custom Parameter 88
- 6.7.5 Message Data 88
- 6.7.7 Tariff Type 89
- 6.7.8 Unrecognised Parameter 90
- 6.8.3 Hop Counter Procedure 94
- 6.8.4 Continuity Testing 95
- Call Set Up 99
- Service 108
- 6.8.6 Message Segmentation 109
- 7 Management Interface 113
- reserved Set to zero 116
- 7.6 Local Overload Request 118
- Parameters 120
- 8 Non-Primitive Interface 121
- 8.3.1 Timer default values 138
- 8.5 Variant Initialisation 141
- operation 142
- message type 142
- 8.8 Read RAM Request 145
- 8.10 Read Circuit Request 146
- 8.11 Read Revision Request 146
- Section 150
- Event specific data 158
- Call states 164
- 8.22 Trace Event Indication 166
- A.1 German ISUP 171
- A.2 UK ISUP 172
- A.3 Japan (TTC) ISUP 173
- A.4 Nortel RLT 174
- A.4.2 Nortel RLT (ITU) 175
- A.5 Italian ISUP 176
- A.6 French ISUP 177
- A.7 China ISUP 178
- A.8 Finnish ISUP 180
- A.9 BICC 180
- Hex Dec Min Max 181
- Reference 181
- ISUP Module 183
- B.2 ITU-T Parameters 184
- B.3 ANSI T1.113 Messages 188
- B.4 ANSI T1.113 Parameters 189
- More Extended Options 195
- Appendix F: Timer Services 199
- F.1 Timer Expiry 200
- Variant Initialisation, 141 203
Relacionado con productos y manuales para Comunicación Welltech Dialogic SS7 Protocols ISUP
Comunicación Welltech WR5100 V.1.0 Manual de usuario
(33 paginas)
(33 paginas)
Comunicación Welltech WG5290 Manual de usuario
(149 paginas)
(149 paginas)
Comunicación Welltech WS 6600 V.2.0 Manual de usuario
(161 paginas)
(161 paginas)
Comunicación Welltech WPoE-808 Manual de usuario
(3 paginas)
(3 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales