Welltech Dialogic SS7 Protocols ISUP Manual de usuario Pagina 80
- Pagina / 203
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Section 6 Interface to Application
80
6.7 Parameter Definitions
The following section defines the parameters that are used in messages
between the local user and ISUP. The parameters are used in the parameter
area of ISP_MSG_TX_REQ (0xc700) and ISP_MSG_RX_IND (0x8701)
messages as detailed in the appropriate message specifications.
Where possible, parameters are defined by reference to either ITU-T Q.763
(1992), ITU-T Q.763 (1997), ITU-T Q.1902.3 (2000) or ANSI T1.113 (1995)
and the format of the parameter is identical to that formatted over the
network.
Where there are differences from the standards, or where additional
information is required for clarity, the parameter is described in subsequent
sub-sections. A set of notes after the table provides further detail where
necessary.
Note: The maximum and minimum length of parameters described below excludes the
name and length octets, whereas they are usually taken into account in ITU-T and
ANSI specs.
Refer to Appendix A: ISUP National Variants on page 171 for the list of
supported national specific parameters.
Value Length
Parameter Name
Hex Dec
Definition/Reference
Min Max
Notes
Access delivery
information
0x2e 46 Q.763 Section 3.2 1 1 1
Access transport 0x03 3 Q.763 Section 3.3
1 255 1
Application transport 0x78 120 Q763 Addenda (09/98) 3 255 1, 4
Automatic Congestion
Level
0x27 39 Q.763 Section 3.4
(09/97)
1 1
Automatic rerouting 0x96 150 Q.1902.3 (amd 3)
section 6.107
1 2 -
Backward call indicators 0x11 17 Q.763 Section 3.5 2 2
Backward GVNS 0x4d 77 Q.763 Section 3.62
(09/97)
1 1 1
Business group 0xc6 198 T1.113 Section 3.3A 9 255 1
Call diversion information 0x36 54 Q.763 Section 3.6 1 1 1
Call diversion treatment
indicators
0x6e 110 Q.763 Section 3.72
(09/97)
1 1 1
Call history information 0x2d 45 Q.763 Section 3.7 2 2 1
Call offering treatment
indicators
0x70 112 Q.763 Section 3.74
(09/97)
1 1 1
Call reference 0x01 1 Q.763 Section 3.8
T1.113 Section 3.5
5 6 1, 2
Call transfer number 0x45 69 Q.763 Section 3.64
(09/97)
2 18 -
Call transfer reference 0x43 67 Q.763 Section 3.65
(09/97)
1 1
- Dialogic 1
- SS7 Protocols 1
- Contents 3
- Figures 6
- Revision History 7
- About this Publication 9
- 1.3 Related Documentation 10
- 1.4 Feature Overview 11
- 2 General Description 13
- Value Mnemonic Meaning 14
- 3 Internal Data Structures 17
- 4.1 System Functions 19
- 4.2 Timer Operation 19
- 5 Interface to MTP 21
- Section 5 Interface to MTP 22
- 6 Interface to Application 23
- 6.2.2 Receive Indication 24
- 6.5.1 Alerting Request 28
- 6.5.6 Confusion Request 32
- 6.5.7 Continuity Request 32
- 6.5.9 Exit Request 33
- 6.5.10 Facility Request 33
- 6.5.11 Facility Response 35
- 6.5.15 Information Request 37
- 6.5.19 Overload Request 40
- 6.5.21 Proceeding request 41
- 6.5.22 Progress Request 42
- 6.5.23 Release Response 43
- 6.5.24 Release Request 44
- 6.5.26 Resume Request 45
- 6.5.27 Segmentation Request 46
- 6.5.28 Setup Request 46
- 6.5.29 Setup Response 49
- 6.5.31 Suspend Request 52
- 6.6.1 Alerting Indication 56
- 6.6.6 Confusion Indication 60
- 6.6.7 Continuity Indication 61
- 6.6.9 Exit Indication 61
- 6.6.10 Facility Indication 62
- 6.6.11 Facility Confirmation 63
- 6.6.19 Overload Indication 68
- 6.6.21 Proceeding Indication 69
- 6.6.22 Progress Indication 70
- 6.6.23 Release Confirmation 71
- 6.6.24 Release Indication 71
- 6.6.26 Resume Indication 73
- 6.6.28 Setup Confirmation 74
- 6.6.29 Setup Indication 76
- 6.6.31 Suspend Indication 79
- 6.7 Parameter Definitions 80
- 6.7.1 Called Party Number 86
- 6.7.2 Calling Party Number 86
- 6.7.3 Cause Indicators 87
- 6.7.4 Custom Parameter 88
- 6.7.5 Message Data 88
- 6.7.7 Tariff Type 89
- 6.7.8 Unrecognised Parameter 90
- 6.8.3 Hop Counter Procedure 94
- 6.8.4 Continuity Testing 95
- Call Set Up 99
- Service 108
- 6.8.6 Message Segmentation 109
- 7 Management Interface 113
- reserved Set to zero 116
- 7.6 Local Overload Request 118
- Parameters 120
- 8 Non-Primitive Interface 121
- 8.3.1 Timer default values 138
- 8.5 Variant Initialisation 141
- operation 142
- message type 142
- 8.8 Read RAM Request 145
- 8.10 Read Circuit Request 146
- 8.11 Read Revision Request 146
- Section 150
- Event specific data 158
- Call states 164
- 8.22 Trace Event Indication 166
- A.1 German ISUP 171
- A.2 UK ISUP 172
- A.3 Japan (TTC) ISUP 173
- A.4 Nortel RLT 174
- A.4.2 Nortel RLT (ITU) 175
- A.5 Italian ISUP 176
- A.6 French ISUP 177
- A.7 China ISUP 178
- A.8 Finnish ISUP 180
- A.9 BICC 180
- Hex Dec Min Max 181
- Reference 181
- ISUP Module 183
- B.2 ITU-T Parameters 184
- B.3 ANSI T1.113 Messages 188
- B.4 ANSI T1.113 Parameters 189
- More Extended Options 195
- Appendix F: Timer Services 199
- F.1 Timer Expiry 200
- Variant Initialisation, 141 203
Relacionado con productos y manuales para Comunicación Welltech Dialogic SS7 Protocols ISUP
Comunicación Welltech WR5100 V.1.0 Manual de usuario
(33 paginas)
(33 paginas)
Comunicación Welltech WG5290 Manual de usuario
(149 paginas)
(149 paginas)
Comunicación Welltech WS 6600 V.2.0 Manual de usuario
(161 paginas)
(161 paginas)
Comunicación Welltech WPoE-808 Manual de usuario
(3 paginas)
(3 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales